EM PM-S Series Pad Mounting Transformer Secondary Connectors (Straight)—Lay-in Type
Description
A secondary connector for a single phase pad mounted transformer with threaded stud secondaries. Available also with either an injection-molded cover as one assembly with the connector, or a loose clear Plastisol-dipped cover.
Features
Conductor is laid in groove.
Accommodates wide range of conductors:
4-350 = #4 AWG – 350 MCM
2-500 = #2 AWG – 500 MCM
40-750 = 4/0 – 750 MCM
40-1000 = 4/0 – 1000 MCM
Connector can be customized to accommodate any number of conductors.
Manufactured from high strength 6061-T6 aluminum for strength and conductivity.
NEETRAC tested to ANSI C119.4.
Dual rated for copper or aluminum.
Benefits
No fighting with conductor to try to “thread” into a set screw hole.
Greater surface contact causes connector to run cooler than others.
*Quick disconnect reduces installation time—simply insert onto threaded stud secondary, and tighten set screw. Also available with full threads and jam nut.
EM PM-Z Series Pad Mounted Transformer Secondary Connectors (Z Bar-Shaped)—Lay-in Type
Description
A secondary connector for a pad mount transformer with quick disconnect for threaded stud secondaries. Accommodates either a 5/8" or a 1" stud mount. Available also with either an injection-molded cover as an assembly with the connector, or a loose clear Plastisol-dipped cover.
Features
Conductor is just laid in from the top.
Accommodates a wide range of conductors:
4-350 = #4 AWG – 350 MCM
2-500 = #2 AWG – 500 MCM
40-750 = 4/0 – 750 MCM
40-1000 = 4/0 – 1000 MCM
Connector can accommodate any number of conductors, plus a street light tap, if desired.
Available as a right-hand or left-hand mount.
Unique pressure pad design engages and disengages with the rotation of the socket head cap screw.
Pressure pad captures the conductor without distorting the strands.
No loose pieces to fall to the bottom of the transformer.
Manufactured from high strength A356-T6 aluminum for strength and conductivity.
NEETRAC tested to ANSI C119.4.
Dual rated for copper or aluminum.
Benefits
No fighting with conductor to try to “thread” into a set screw hole.
Greater surface contact causes connector to run cooler than others.
EM CB Series Pad Mounted Transformer Secondary Connectors (Straight)—Set Screw Type
Description
A secondary connector for a single phase pad mounted transformer with threaded stud secondaries. Can be ordered with anodized set screws to prevent galling.
Features
Accommodates wide range of conductors.
Connector can be customized to accommodate any number of conductors.
Manufactured from high strength 6061-T6 aluminum for strength and conductivity.
Dual rated for copper or aluminum.
Can be individually shrink-wrapped to keep joint compound clean and intact.
EM Z Series Pad Mounted Transformer Secondary Connectors (Z Bar-Shaped)—Set Screw Type
Description
A secondary connector for a pad mount transformer with quick disconnect for threaded stud secondaries. Accommodates either a 5/8" or a 1" stud mount. Can be ordered with anodized set screws to prevent galling.
Features
Accommodates a wide range of conductors.
Connector can accommodate any number of conductors, plus a street light tap, if desired.
Manufactured from high strength 6061-T6 aluminum for strength and conductivity.
Available as a right-hand or left-hand mount.
NEETRAC tested to ANSI C119.4.
Dual rated for copper or aluminum.
Compact design increases cable capacity.
Can be individually shrink-wrapped to keep joint compound clean and intact.
*Quick disconnect reduces installation time—simply insert onto threaded stud secondary, and tighten set screw. Also available with full thread and jam nut.
